STAMP MIX
CEMENT MIXES
DECORATIVE PRODUCTS
STAMPED CONCRETE FINISH
OVERLAY STAMP MIX is a polymer modified cementitious coating used as an overlay on existing concrete surfaces to achieve a decorative stamped appearance. Designed for resurfacing structurally sound, non-moving concrete. Ideal for worn, discolored, out-of-level substrates. Coverage is approximately 35 sf/bag at 3/8” thickness.
SUITABLE SUBSTRATE
Concrete
AVAILABLE COLORS
| COVERAGE |
| Per Bag: 30 – 35 ft 2 |
AVAILABLE SIZES
| 65 Lb Bag |
SURFACE PREPARATION:
Substrate must be structurally sound, free from grease, oil, paint, dirt, dust, sealers. Laitance, curing compounds, and any other foreign material which may prevent proper bonding. A layer of Multicoat’s SCRATCH KOTE 2000 must be applied to the substrate and allowed to dry prior to OVERLAY STAMP MIX application.
MIXING:
OVERLAY STAMP MIX is field mixed with clean potable water to desired consistency based upon scope of application. Add no more than 1½ gallons of water per bag. Mix vigorously with a Multicoat Cage Mixer to disperse all lumps and to thoroughly wet all particles. Adjust to desired consistency by addition of dry material or small amount of water. Mix thoroughly for a maximum of 3 minutes. For best results allow material to set for 3 to 5 minutes, then add a small amount of water and re-break the material.
APPLICATION:
OVERLAY STAMP MIX is typically applied via gauge rake to a consistent thickness of not more than 1/4”. Be sure to keep a wet edge to prevent cold joints from occurring. Allow STAMP MIX to progress to a stiff plastic condition prior to application of the stamps. Spray stamp mats with stamp release spray and place onto Overlay Stamp Mix and imprint to desired texture and effect. Mats will have to be cleaned and release spray applied periodically to prevent sticking.
COLOR:
OVERLAY STAMP MIX should be allowed to dry overnight. The entire surface should be hosed and scrubbed down to remove any remaining release material which has not evaporated. We recommend the use of our MUILTI-STAIN for the final color. Follow directions for MULTI- STAIN found on the pails or instruction sheet.
CURING:
OVERLAY STAMP MIX will harden in approx. 24 hours, and will reach its full strength potential in 28 days. Curing time will vary due to weather conditions, thickness, substrate absorption, etc. Material should be protected from weather elements for a minimum of 24 hours.
LIMITATIONS:
Do not apply if substrate temperature is below 40°F or above 100°F, or if ambient temperature below 40°F above 100°F. Do not apply if precipitation is expected within a twenty four (24) hour period. Do not add other materials to the mixture of the product.
SIZES:
- 65 lb bag
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
1. Multicoat system has been properly applied by a certified applicator.
2. Problem is determined to be due to defect of Multicoat Corporation’s products.
3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane.
Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, de-bonding and water intrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
1. Use only a licensed contractor in good standing (fully bonded).
2. Make certain that the applicator has been certified by Multicoat, prior to work
commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in
good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within
manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the
Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential,
resulting from its products. The parties intend that the limitation of damages,
including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
SURFACE PREPARATION:
Substrate must be structurally sound, free from grease, oil, paint, dirt, dust, sealers. Laitance, curing compounds, and any other foreign material which may prevent proper bonding. A layer of Multicoat’s SCRATCH KOTE 2000 must be applied to the substrate and allowed to dry prior to OVERLAY STAMP MIX application.
MIXING:
OVERLAY STAMP MIX is field mixed with clean potable water to desired consistency based upon scope of application. Add no more than 1½ gallons of water per bag. Mix vigorously with a Multicoat Cage Mixer to disperse all lumps and to thoroughly wet all particles. Adjust to desired consistency by addition of dry material or small amount of water. Mix thoroughly for a maximum of 3 minutes. For best results allow material to set for 3 to 5 minutes, then add a small amount of water and re-break the material.
APPLICATION:
OVERLAY STAMP MIX is typically applied via gauge rake to a consistent thickness of not more than 1/4”. Be sure to keep a wet edge to prevent cold joints from occurring. Allow STAMP MIX to progress to a stiff plastic condition prior to application of the stamps. Spray stamp mats with stamp release spray and place onto Overlay Stamp Mix and imprint to desired texture and effect. Mats will have to be cleaned and release spray applied periodically to prevent sticking.
COLOR:
OVERLAY STAMP MIX should be allowed to dry overnight. The entire surface should be hosed and scrubbed down to remove any remaining release material which has not evaporated. We recommend the use of our MUILTI-STAIN for the final color. Follow directions for MULTI- STAIN found on the pails or instruction sheet.
CURING:
OVERLAY STAMP MIX will harden in approx. 24 hours, and will reach its full strength potential in 28 days. Curing time will vary due to weather conditions, thickness, substrate absorption, etc. Material should be protected from weather elements for a minimum of 24 hours.
LIMITATIONS:
Do not apply if substrate temperature is below 40°F or above 100°F, or if ambient temperature below 40°F above 100°F. Do not apply if precipitation is expected within a twenty four (24) hour period. Do not add other materials to the mixture of the product.
SIZES:
- 65 lb bag
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
1. Multicoat system has been properly applied by a certified applicator.
2. Problem is determined to be due to defect of Multicoat Corporation’s products.
3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane.
Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, de-bonding and water intrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
1. Use only a licensed contractor in good standing (fully bonded).
2. Make certain that the applicator has been certified by Multicoat, prior to work
commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in
good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within
manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the
Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential,
resulting from its products. The parties intend that the limitation of damages,
including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
