SPEED BOND
URETHANE CRACK REPAIR CAULKING
Speed Bond is a two-part, self leveling, rapid set, urethane caulking used to fix cracks in horizontal concrete. Sets up fast like an epoxy, however the urethane composition allows it to remain somewhat flexible. Each tube comes with 1 mixing tip. Uses a standard caulking gun.
SUITABLE SUBSTRATE
Wood
Concrete
AVAILABLE COLORS
| COVERAGE |
| Per Tube: 40 Linear ft |
AVAILABLE SIZES
| Dual Cartridge Tube |
SURFACE PREPARATION
Surface must be completely dry and thoroughly clean of any foreign material that may interfere with bonding. Cracks larger than 1/16” in width must be opened with a crack chaser to a minimum of 1/4” in width. Once opened, all cracks must be cleaned by sand-blasting, waterblasting
or water sandblasting. Depth of crack and surface area around crack must be completely dry and thoroughly clean.
APPLICATION
Prepare Cartridge: Unscrew round colleet, pull cap from center of tube and set both to the side for later use. Screw enclosed mixing tip onto tube insuring snug fit.
Initial Dispense: Prior to filling crack, insure material is flowing through mixing tip uniformly and easily. Dispense onto discarded cardboard as a test.
Begin filling crack to a slightly over filled capacity, then immediately press SPEED BOND into crack and spread material level and flat onto adjacent sides of crack by using a margin trowel or putty knife. While SPEED BOND is wet, broadcast #16-20 silica sand generously over the wet SPEED BOND and allow to set until dry. Once dry, brush away and sand that has not stuck to the SPEED BOND. The crack is now ready to be over-coated. Speed Bond is self leveling, and large cracks that are completely open should be dammed closed to prevent the SPEED BOND from leaking out the bottom.
Reuse: Partially used tubes can be stored and re-used. Remove the used mixing tip and discard as they can not be re-used. Attempting to re-use a used mixing tip will damage the tube and render it useless. After used tip has been removed, wipe excess material from end of cartridge, re-install the cap and collet.
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
- 1. Multicoat system has been properly applied by a certified applicator.
- 2. Problem is determined to be due to defect of Multicoat Corporation’s products.
- 3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane. Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, debonding and water instrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
- 1. Use only a licensed contractor in good standing (fully bonded).
- 2. Make certain that the applicator has been certified by Multicoat, prior to work commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential, resulting from its products. The parties intend that the limitation of damages, including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
SURFACE PREPARATION
Surface must be completely dry and thoroughly clean of any foreign material that may interfere with bonding. Cracks larger than 1/16” in width must be opened with a crack chaser to a minimum of 1/4” in width. Once opened, all cracks must be cleaned by sand-blasting, waterblasting
or water sandblasting. Depth of crack and surface area around crack must be completely dry and thoroughly clean.
APPLICATION
Prepare Cartridge: Unscrew round colleet, pull cap from center of tube and set both to the side for later use. Screw enclosed mixing tip onto tube insuring snug fit.
Initial Dispense: Prior to filling crack, insure material is flowing through mixing tip uniformly and easily. Dispense onto discarded cardboard as a test.
Begin filling crack to a slightly over filled capacity, then immediately press SPEED BOND into crack and spread material level and flat onto adjacent sides of crack by using a margin trowel or putty knife. While SPEED BOND is wet, broadcast #16-20 silica sand generously over the wet SPEED BOND and allow to set until dry. Once dry, brush away and sand that has not stuck to the SPEED BOND. The crack is now ready to be over-coated. Speed Bond is self leveling, and large cracks that are completely open should be dammed closed to prevent the SPEED BOND from leaking out the bottom.
Reuse: Partially used tubes can be stored and re-used. Remove the used mixing tip and discard as they can not be re-used. Attempting to re-use a used mixing tip will damage the tube and render it useless. After used tip has been removed, wipe excess material from end of cartridge, re-install the cap and collet.
STORAGE:
- 40-90°F.
- Low humidity environment
SHELF LIFE:
- Approx. 24 months in unopened containers.
Multicoat Corporation offers a special 5-year Limited Materials Warranty to Trained and Certified Applicators. This Limited Warranty (effective upon date of purchase) protects the Applicator against delamination problems with all Multicoat systems, as well as water intrusion of Multicoat’s Waterproofing System, provided:
- 1. Multicoat system has been properly applied by a certified applicator.
- 2. Problem is determined to be due to defect of Multicoat Corporation’s products.
- 3. Applicator has prepared and filed the required Warranty Information Form(s) with Multicoat Products, Inc. covering the specific customer job(s).
NOTE:
Warranty is not applicable if there is movement or cracking of the underlying base and/or the weight bearing cement covering of the waterproofing membrane. Failure to adhere to good construction and workmanship practices based on industry standard construction, means, methods, sequences and techniques could result in delamination, debonding and water instrusion for which Multicoat will not be responsible.
The end user must look to the Certified Applicator for satisfaction if any problem develops with the Multicoat system covered by the warranty. Multicoat suggests that the customer:
- 1. Use only a licensed contractor in good standing (fully bonded).
- 2. Make certain that the applicator has been certified by Multicoat, prior to work commencing or certification while on the job. A simple phone call to Multicoat is sufficient to determine if an applicator is certified and if such certification is in good standing.
In the event that it is determined that the Applicator failed to install the system(s) in accordance with Multicoat’s “instructions for use” or “specifications”, the warranty is void. See specific warranty information below.
WARRANTY
Materials are guaranteed with respect to uniformity and quality within manufacturer’s specifications.
WARRANTY DISCLAIMER
There are no warranties which extend beyond the description of the fact hereof. Seller expressly disclaims all other warranties regarding the use of its products, whether expressed or implied, including the implied warranties of merchantability and for fitness of a particular purpose. Since use of the product is beyond the Seller’s control, the Buyer assumes all risk of use.
EXCLUSIVE REMEDY
Seller’s sole obligation, and buyer’s exclusive remedy shall be to replace material if found to be defective.
DAMAGE LIMITATION
Seller shall not be liable for any damages, injury, loss, direct or consequential, resulting from its products. The parties intend that the limitation of damages, including consequential damages, applies even if the exclusive remedy provided for herein fails of its essential purpose.
